[DX11] Help regarding Nvidia Profile Inspector (NPI)

[JHTrucker]

@BenganJ

Far too hard for me:-
(normalized_ui_width + 2 x normalized_ui_x) = 1.0

Simpler!
(1-width)/2=x

On your first post you have:-
'Mirror Quality' -----'High' //For this scheme to work properly this setting is a MUST! At least for now.

Still not good enough? There's no pleasing some people!

The only minor problem i can think of is if, at some point in the future, the game crashes because of a bad mod and the game resets your config to low settings on re-entry... will that reset munltimon_mode back to default "0"?. Then suddenly lots of my gfx are flipping WTF!!!
Also people deleting config to allow game to generate a new one for what ever reason.

Time will tell.

Thanks for all the thanks guys.
It was a team effort... good initial ground work that proved the impossible was possible after all. I just got the right bit of luck (15 minutes with the AA bit!) and a tidy up.

[BenganJ]

Now I ONLY wish for ReShade to be working too, but to be honest, I haven't
tried it thoroughly yet. May be time for that now, as ReShade isn't all about good
looking graphics. The package I use, linked to in the first post, gives me the
oppurtunity to watch the game in 3D VR in a HMD through creating the imagery
on the game PC, transferring it over WiFi to my phone mounted in a cheap
VR headset!

[BenganJ]

@JHTrucker

There's a reason why I have a copy of my config.cfg file in case
the game crashes and destroys my settings!

EDIT: Mirror Quality comment edited! Thanx mate! :D

[JHTrucker]

@BenganJ
Quick update regarding monitor sizes:-
The wider the monitor, the wider the UI.
So your 1920x1080 has the UI filling that space nicely.
My monitor 3840x1024 has the UI also filling that space.
Some may not like it, imagine 2 of your monitors together and the drive button was on left monitor, far left and profiles on right, far right.
For people who just want a UI centred but the same size as your 1920x1080 with the left 960 and right 960 being blank, can mod the mmcfg file to 0.5 width.

If you want to see what i mean or see what different res monitors would look like:
Assume 1920x1080 monitor is being used for this test.
set game as windowed.
Res 1920x512 (3840x1024 aspect)
Check game.

Res 1920x810 (2560x1080 aspect)
etc.

[clear F1]

Please give me ReShade! :)
good night.

[Kiszlo]

Hello, unfortunately it does not work for me, zero response after setting in NPI, everything still looks the same. Any advice?

[BenganJ]

@Kiszlo

Please, think about this yourself. If someone came to you and said "It does not work for me!",
would you directly have a solution to that? We need of course as much as possible of your
configurations, NPI, config.cfg, game log (to see if something else is your problem). Have
you installed the multiMon config? Have you set Scaling to 100% in game and SMAA disabled?

[Kiszlo]

@Kiszlo

Please, think about this yourself. If someone came to you and said "It does not work for me!",
would you directly have a solution to that? We need of course as much as possible of your
configurations, NPI, config.cfg, game log (to see if something else is your problem). Have
you installed the multiMon config? Have you set Scaling to 100% in game and SMAA disabled?

I can configure, but the desktop is not clear, can it be improved?

[BenganJ]

@Kiszlo

Yes, it can be improved, but ONLY if you give us all the configurations you have done.
READ MY PREVIOUS POST!

[Kiszlo]

@Kiszlo

Yes, it can be improved, but ONLY if you give us all the configurations you have done.
READ MY PREVIOUS POST!

My npi settings :
config.cfg -http://www.wklejto.pl/808848
game.log - http://www.wklejto.pl/808849
NCP-