[DX11] Help regarding Nvidia Profile Inspector (NPI)

[KARU0920]

https://github.com/crosire/reshade-shaders/tree/nvidia
Can't I still use Reshade's Shader with Nvidia Free Style in this way?

[BenganJ]

@KARU0920

Yes you can, especially with those granted shaders. I have them installed in my Freestyle folder
and it works well. ENJOY!

[JHTrucker]

@BenganJ - Updated that link, thanks.
Nothing to do, just putting what i have there in case it inspires someone to complete it or work out a better solution.
If you were bored and have all that's required to test it (logitech or similar for key recording), and can follow what i've written, then feel free to test with a w900.
The fact that the block isn't an in game option to set means you can't enable it without realising what you are doing. so scs not allowing TIR users to use/try/turn off is strange. I think they couldn't do it as easy as mouse block and just made up that reason.
But, I suspect even mouse users have now become bored of the block and are back to just passing through the window.

[BenganJ]

@JHTrucker

Right, I agree! Sometimes SCS does half-heartedly things, maybe in order to complete them later,
I'll have a closer look at what you have produced later, right now time does not permit.

[Ronin]

Smaller view 8 - Has image 85% height and 100% width (black bars top and bottom)

V8 =1762560

@JHTrucker

Can you check Smaller View 8.
I think it has;
- image 70% height an 100% width (black bars top and bottom)
- V8=1344000

But I am curious about the other Smaller view 8 version which you describe.

[clear F1]

@ JHTrucker, @ Bengan

test conditions:
ETS2 was uninstalled and reinstalled.

Map YKSRSK-SRmap_roadconnection_V-2.2.1
From Kutaisi (GE) to SR map

DSR x1.78 (1440p)
Vsync "2" (30fps)

config.cfg
uset g_lod_factor_pedestrian "1"
uset g_lod_factor_parked "1"
uset g_lod_factor_traffic "1"
Others are recommended values ​​on the first page.

Top-level game_data.sii
leaves_lod_start: (240.0, 410.0, 50.0)
leaves_lod_end: (300.0, 460.0, 100.0)

Nvidia driver 442.74
NPI 2.3.0.10

NPI settings
4x [4x Multisampling]
4x Sparse Grid Supersampling
Others are recommended values ​​on the first page.

It is 20fps as before.
Tearing also occurs when turning in urban areas. :(

--------------------
1080p60 was a treasure trove.
1080p30 (fps limiter 30) also gets fps20.
After this post, test with Vsync "2" 1080p30.
--------------------
Question:
2560x1440 (WQHD 75hz or higher or G-Syinc compatible monitor) Do you think that you can operate 1440P with GTX1070 without DSR?

[clear F1]

I tried Vsync "2" 1080p30 with the above conditions and Lod settings, but 20fps happens continuously. It will be a level where you cannot drive normally.

[BenganJ]

@clear F1

I still think this is an odd case! Please, can you run the same route with the same settings, EXCEPT having NO V-SYNC,
or FRAME LIMITER at all set. If possible, record with OSD showing FPS and if you have the opportunity to measure
the MIN, AVERAGE and MAX FPS values too, it would be nice.

[clear F1]

@BenganJ

I removed all but the map mod a few hours ago. But the result was the same.
Before we see what my friends wrote, I am currently restoring from C drive disk backup on April 16th. For the time being, I hope that recording will be possible at 1080p.

[BenganJ]

@clear F1

Okay my friend, I am keeping my fingers crossed here that you will get
going again on that machine. Report back, please!